-
June 2023 by Luis Calderon
drove bout 120. from milwaukee to this place because most of the reviews were good. but i regret it...took my sbc 327 for engine block for machining,, asked to give me all parts needed to be re assembled along with new pistons. since im doing the work my self, Not my first time building an engine.. when it came to assembly the Main Cap #4 was not machined properly. when given the torque the crank would not turn over..Gave them a call and took back the block for recheck.. Bout a week after got a call back and said it was ready. they said the main caps were somehow bad or incorrectly installed and charged me $400.00 extra. i asked if that wasnt supposed to be done in the begining. the crank should be one of the most important thing to get looked at when rebuilding an engine.. the said no it wasnt done.Got back home started assemble the rest of the parts to find the That the piston rod on cylinder 8 was installed in the wrong direction to were it should go..i have to find another place to reinstall the rod corretly..Don bring your stuff here.. friendly staff but not so good quality work.
-
November 2020 by Joe K
Had a 347 stroker engine built by powersource, biggest mistake in my life.The engine had a bad oil leak from rear main turns out when they align bored the mains the broke a chunk of the rear main cap and tried to seal with with silicone.They said they would fix the leak. They did something and told me it was fixed.I installed engine and it ran for 20 minutes then started leaking oil again.I removed the engine and looked for the issue myself and found powersource did a hack job and won't own up to it.I end up getting another engine since no other shop will touch anything powersource built.Plenty of other shops but do not support this place or you will regret it. Ray is a horrible guy to trust any work with.
-
April 2020 by jon rocklin
Recently got my motor done here and they went through and through with me throughout the entire process. Great set of people
-
September 2019 by D S.
I took a motorcycle cylinder there for them to LOOK at. Ray says, ok I'll give you a call tomorrow. Against my better judgment, I left it there. I was expecting it to be looked at while I was there since it takes 5 minutes.... I had to call them the next day to see what the status was. I needed to know if it was OK to run, or do I need to buy a bigger piston and bore it. He says the bore is too big, get a piston. Ok. So I said I would be over to get my stuff and will be back with it all when I get the bigger piston. He says ok, $30. I hang up the phone. lol $30. Typically inspection and measuring is free. He never told me it was going to cost me something for them to evaluate and I know it only takes 5 minutes to measure...... BECAUSE I ALREADY DID THAT MYSELF!!!! I was concerned with the condition! So I get there and argued the $30 for his 5 minutes of work and he tells me it was 30 minutes. I figured he would argue with me so I payed him. Why? To let him sell his integrity for $30 and his lies. I doubt he even did anything with my cylinder aside from look at it and he wanted it over night so he lie to me and tell me he measured it. Every other time I take a cylinder someplace, they grab their tools and measure it on the spot. This guy obviously really needed the $30 bucks. Many years ago he stole an aluminum Nascar block from a close friend of mine and used it on one of their own race motors or a customers and replaced it with an off the shelf iron block. Liars and thieves and I have no clue how they are still in business. Who knows maybe the place is just a front to launder money?
-
September 2019 by American Classic Muscle Cars Classic Cars
Just WON my National Championship these guys are the Best
-
May 2019 by Robert Hansen
Good if you want basic work I went there thought it was a good place good reviews. He worked with payments while he was rebuilding the engine I went there for a performance build my car had low hp 180hp factory I was going to replace the engine with a 383 crate from jegs I was told not to do that he could wake up my engine if I paid more money I was told by the mechanic I was going to have around 400 to 425 hp the max amount for that engine I was lied to at only has 230 dyno tested way under rated I asked how much my compressor was I was told 9.71 to 1 he put factory pistons in it rated around 8.5 to 1 compression another lie when I went in and told him it felt slow he said he would tune it and get more power I said I would rather have it dyno tuned something felt off he get very pushy into not wanting me to do that good thing I did found out a lot about how bad he did do not go there he will over charge you and give you nothing you want I need to re build my engine again spent 4 grand for nothing have to drop another 2500 should have just replaced the engine don't let him lie to you too
-
April 2019 by Robert H.
Good if you want basic work I went there thought it was a good place good reviews. He worked with payments well he was rebuilding the engine I went there for a performance build my car had low hp 180hp factory I was going to replace the engine with a 383 crate from jegs I was told not to do that he could wake up my engine if I paid more money I was told by the mechanic I was going to have around 400 to 425 hp the max amount for that engine I was lied to at only has 230 dyno tested way under rated I asked how much my compressor was I was told 9.71 to 1 he put factory pistons in it rated around 8.5 to 1 compression another lie when I went in and told him it felt slow he said he would tune it and get more power I said I would rather have it dyno tuned something felt off he get very pushy into not wanting me to do that good thing I did found out a lot about how bad he did do not go there he will over charge you and give you nothing you want I need to re build my engine again spent 4 grand for nothing have to drop another 2500 should have just replaced the engine don't let him lie to you too
-
March 2019 by G M.
had a big block chevy built great horsepower no issues very happy with price and done in time frame quoted to me I will do business with them again
-
October 2018 by Kyle Vanduser
Had my engine rebuilt over the winter by powesource. Very good customer service and worked with me to have the boat all ready to go by memorial weekend despite flooding. Glad I chose to go with them. Solid work and knowledge. Thank you!
-
October 2018 by James Krueger
Took my 604 their for a rebuild, got it done timely and did what he said he would do. Answers the phone every time you call and is easy to get ahold of.
-
October 2018 by Petegina Jarvis
Used them 2 times and was always happy with the Service I received
-
October 2017 by Advantage Material Handling
Great work and service. We have used multiple times and will continue to use. Try them and see for yourself.
